Pcb assembly provider with bstpcb.com? Since beginning, as a printed circuit board (PCB) vendor in Asia, Best Technology is dedicating to be your best partner of advance, high-precision printed circuit boards, such as heavy copper boards, ultra thin PCB, mixed layers, high TG, HDI, high frequency (Rogers, Taconic), impedance controlled board, Metal Core PCB (MCPCB) such as Aluminum PCB, Copper PCB, and Ceramic PCB (conductor Copper, AgPd, Au, etc) and so on. Find more information at printed circuit board manufacturers. The layer on top of the copper foil is called the soldermask layer. This layer gives the PCB its green (or, at PCB & MCPCB, red) color. It is overlaid onto the copper layer to insulate the copper traces from accidental contact with other metal, solder, or conductive bits. This layer helps the user to solder to the correct places and prevent solder jumpers. In the example below, the green solder mask is applied to the majority of the PCB, covering up the small traces but leaving the silver rings and SMD pads exposed so they can be soldered to. Soldermask is most commonly green in color but nearly any color is possible. We use red for almost all the PCB & MCPCB boards, white for the IOIO board, and purple for the Best Technology boards.
Best Through Hole Technology assemble more than 50 kinds components Factory Price. We offer a complete range of through hole PCB assembly capabilities in compliance with IPC quality standards. We provide Through Hole Technology (THT) PCBA service at the highest quality level and in a cost-effective manner. Our through hole technology (THT) PCB Assembly services includes both manual and automated techniques. While our manual soldering techniques can handle complex assemblies, the automated ones are best suited for high volume production as well as reduced material handling. We provide THT PCBA service at the highest quality level and in a cost-effective manner. Quality Policy: PCB Quality is the core of products. All of engineer & vital department guys has more than five years expenrience in PCB industry, we follow up the default PCB standard, as well as with clients’ special request.
In order to provide one-stop-services to customers, we can also provide FPC and Rigid-flex PCB Assembly service (also named SMT: Surface Mounting Technology). We can purchase all components from abroad or domestic market, and provide full products to you with short lead time. High Density Interconnects (HDI) board are defined as a board (PCB) with a higher wiring density per unit area than conventional printed circuit boards (PCB). They have finer lines and spaces (<100 µm), smaller vias (<150 µm) and capture pads (300, and higher connection pad density (>20 pads/cm2) than employed in conventional PCB technology. HDI board is used to reduce size and weight, as well as to enhance electrical performance.
Today printed wiring (circuit) boards are used in virtually all but the simplest commercially produced electronic devices, and allow fully automated assembly processes that were not possible or practical in earlier era tag type circuit assembly processes. A PCB populated with electronic components is called a printed circuit assembly (PCA), printed circuit board assembly or PCB Assembly (PCBA). In informal use the term “PCB” is used both for bare and assembled boards, the context clarifying the meaning. The IPC preferred term for populated boards is CCA, circuit card assembly. This does not apply to backplanes; assembled backplanes are called backplane assemblies by the IPC.
According to different manufacturing method, current there’re three basic types for ceramic board: A) Thick Film Ceramic Board Thick Film Ceramic PCB: Using this technology, the thickness of conductor layer exceeds 10 micron, more thick than spurting technology. The conductor is silver or gold palladium, and was printed on ceramic substrate. More for Thick Film Ceramic PCB. B) DCB Ceramic Board DCB (Direct Copper Bonded) technology denotes a special process in which the copper foil and the core (Al2O3 or ALN), on one or both sides, are directly bonded under appropriate high temperature and pressure. Find extra info on bstpcb.com.
Generally speaking, aluminum is the most economic option considering thermal conductivity, rigidness, and cost. Therefore, the base/core material of normal Metal Core PCB are made of aluminum. In our company, if not special request, or notes, the metal core refer will be aluminum, then MCPCB will means Aluminum Core PCB. If you need Copper Core PCB, Steel Core PCB, or Stainless steel core PCB, you should add special notes in drawing.